How to Deal with Weigh Safe Hitch Problems?

A weigh-safe hitch is a built-in scale combined with an adjustable hitch. It is the only type of trailer hitch that comes with a load adjustment indicator that is built-in. This invention made towing to become safer.

However, a mess can result in massive losses if you are faced with weigh-safe hitch problems. In this article, we will discuss how to deal with Weigh Safe Hitch Problems. Let’s get into it.

Which are some of the common issues associated with the Weigh Safe Hitch?

In most cases, users face three major issues with the weigh-safe hitch. It can be either it has broken down, the ball is playing too much, or it’s an issue to do with misalignment. Once you encounter any of these issues, you will need to find a solution quickly. Here are some possible solutions:

First, you need to take all the required measurements. Make sure you are focusing on the outer side of the trailer’s frame. Take your measurement from the middle of the coupler. Proceed for 32 inches on both sides and make some marks using a pencil or any other marking tool. Then you need to take your weight circle measurement.
The mark you make plays a vital role in the sway bracket assembly. Before getting to the point where you get the link plates installation, there are a couple of things you should clear out. First, ensure that you’ve checked the trailer’s frame and confirm that no wires are going around it. Doing that will help you avoid a subpar installation.
Next, you want to re-route the wires as much as possible. That should be enough to keep them from getting damaged by the link plates. Upon doing that, you can proceed to the installation of the plate.
If you are accurate and put the bracket to exactly 32 inches, you will be putting the least pressure on the hitch components and the trailer. For that reason, the ride gets more comfortable and safe.
If you cannot place the brackets at precisely 32 inches, you will need to use link plates to close the coupler. In that case, ensure the minimum distance is about 27 inches in the center.

Increasing The Movement Of the Hitch Ball

This refers to a situation where the trailer is rolling in a horizontal direction. It seems to be moving side to side instead of going straight ahead. The weigh safe-2 ball mount movement increases to a speed of 2.5-inch hitch.

You need to know that something with a built-in scale of a 2-ball mount does not require a lot of play. The first thing you need to do is confirm that the ball-holding pin is firm and is holding the ball correctly.

There are times when the hitch ball proves to be on the wrong side. Ensure that the ball fits correctly on the trailer and can handle the weight you are pulling.

Normally people hung to the belief that a slight play of the ball can cause a major disaster. This is not true, but increased movements should be avoided at all costs.

What to do if the Weight Safe Hitch gets Broken?

There are times when the weight-safe hitch gets broken. If that is the case, what should one do? Panicking won’t help at all. Here are the instructions you need to follow.
You must have a strong center punch or screwdriver, a hammer, a table vice, as well as a sledge hummer. With these, you should begin.

The first thing you should do is set the hitch assembly on a flat surface. A table vice will come in handy at this point. The hitch slide part will require support underneath. Doing that will make the pins of the slider locker remain unsupported.
You can also decide to set it on grass. If that is the case, a rag or cloth will be of much help. That will ensure that the finish is guarded properly. Once you clamp the hitch, you will notice that there will be no further movements.
On the side of the lock, you’ll find the pins. Screw them in using the screwdriver one after another. You can also use a canter punch as an alternative. After that, use the hammer to knock down the pinhead so that they slide out of the lock plate. Upon doing that, the lock plate and the lock itself will remain hooked to the slider. And since you would like to start rotating the plate at a 10-degree motion in a clockwise manner, that will be good.

Once you’ve done that, you are good to go.

More: What size floor jack is needed for a Ford F150?

Frequently Asked Questions (FAQs)

Are weigh-safe hitches accurate?

Well, the accuracy of a weigh-safe hitch can vary from time to time. Some come with an adjustable torque weight that can be adjusted at the factory. This is the type that we are talking about. Some weigh-safe hitches are accurate as long as they’re not defective. Such true tows will give you accurate results, ensuring a safer towing experience.

Where are weigh-safe hitches made?

Most of the Weigh safe hitches available are made in Lindon, Utah, USA. This means they are of high quality and very sturdy. They’re designed with the aim of providing you with a safe towing experience.

When making a purchase, you need to make sure that you do not compromise on quality. Check for the logo indicating where it is made from. Those made in the USA come with a limited warranty which is extremely good.

How does it work?

This device works extremely easily with the trailer pushing down that ball away from the hitch, making it light. The ball pushes the pressure down via the internal hydraulic piston, which sits perfectly on the oiled bed. That is how the reading is achieved.

Final Thoughts

With the information discussed in this article, one can perfectly solve problems associated with a weigh-safe hitch. You should note hit rock bottom when faced with such a challenge. The weigh-safe hitch is the best when it comes to safety. It’s a great help, especially when you are pulling a heavy load. Knowing how to use it perfectly will help you avoid any mishaps.